Product Description
-------------------
Control loads with the receiver ed ON/OFF button or
wirelessly via a remote transmitter. GENERAL INFORMATION: These
Modular Radio Receivers are one half of a two part remote control
system. They operate as ordinary ON/OFF switches but they also
respond to the signals of a hand held transmitter - the other
half of the system. The modules are designed for indoor or
outdoor use, and can handle a variety of sw applications,
typical around the house or farm. By the push of a button on the
face of the transmitter, the user is able to turn ON/OFF the
connected load (lights, pump, etc.) from any remote location*,
safely and conveniently. In addition, a single transmitter can
operate up to three Receivers and is able to “teach” each Module
a different code. (Transmitters are sold separately). Model RC613
Receiver Module comes with its own manual ON/OFF button and it is
intended to be installed at the location of the load. The
connected load may be turned ON/OFF using the hand-held
transmitter or turned ON/OFF by pushing the red button on the
face of the Receiver. Model RC613L Receiver Module is the same as
RC613 except that it comes with extra long (36 in.) leads. * The
open field range is approximately 200 feet or less, but depends
on many factors like the age of the battery, proximity of large
metal objects, the location of the receiver and environmental
conditions at the time of transmission. SPECIFICATIONS AND OTHER
INFORMATION: USEFUL INFORMATION 1. Must be ed upright.
Antenna must be up. 2. Radio Receivers are sensitive to heat.
Avoid ing them above heater, air conditioner or exposed to
afternoon sun. 3. The higher the Receiver Module, the longer its
range. For good range and reliable reception, install modules as
high as practical above ground level with antenna at top. 4.
Large metal objects divert radio signals. Avoid ing Receiver
Modules on metal wall, fence or near large metal objects. 5.
Environmental conditions could effect the operation of the remote
control system. For example, in rain the range may be less than
normal. 6. Certain electric equipment like brush type motors or
electronic heater igniters emit radio signals and can effect
the function of the Receiver Module. Avoid ing modules near
such equipment. 7. To prevent electronic interference, install
Receiver Modules at least 3 feet apart. INSTALLATION: 1. Attach
Receiver Module to the top of an outdoor grade junction box. Make
sure the assembly is raintight. 2. Select the proper location
(see Useful Information above) and install Receiver assembly on a
vertical surface or other support, using hardware, suitable for
the purpose. 3. Prepare the necessary conduit runs as required by
the installation layout and pull-in the specified conductors. 4.
Follow wiring diagram A on the right, make wire connections as
shown. 5. Turn ON power and test installation, using the ON/OFF
button on face of the Receiver Module. Replace junction box
cover, make sure the installation is secure and raintight. 6. To
link transmitter button with the receiver, see Operating
Instructions on page 3. OPERATION: Linking RC939 Transmitter
Button with the RC613 Receiver 1. To clear any existing codes,
press and hold the blue code set button on the receiver for 15
seconds then release. 2. Now insert a paper clip in the hole on
the bottom right side of remote and get the red light on the
bottom to light up. (NOTE: Illuminated LED may be difficult to
see in direct sunlight.) 3. To link the reciever and transmitter,
go back to the receiver and press & release the blue code set
button. 4. Now choose the button on the remote you want it on and
SLOWLY ”press & release”. 5. After the 7th time, you should hear
the relay in the receiver click. 6. Continue to SLOWLY press the
remote button (relay should click every 4th time now). 7. Repeat
until you hear the relay click 3 or 4 times. 8. Press one of the
other 2 buttons on the remote to save the code. Linking Multiple
transmitters with a Receiver Up to three different transmitters
can control a receiver. Follow steps 1 through 4 of Linking each
RC939 transmitter with the RC613 receiver. 3
From the Manufacturer
---------------------
These Modular Radio Receivers are one half of a two part remote
control system. They operate as ordinary ON/OFF switches but they
also respond to the signals of a hand held transmitter-the other
half of the system. The modules are designed for indoor or
outdoor use, and can handle a variety of sw applications.
By the push of a button on the face of the transmitter, the user
is able to turn ON/OFF the connected load (lights, pump, etc.)
from any remote location, inside or outside of the house, safely
and conveniently. In addition, a single transmitter can operate
up to three receivers and is able to "teach" each module a
different code (Transmitter model RC939 sold separately).
- Respond to handheld transmitter.
- For indoor/outdoor use.
- Handle a variety of sw applications.
- Enable conNECted loads to be turned ON/OFF remotely.